PlanMeca X-Ray Systems Repairs- various locations across Canada

Trade Agreement: NAFTA/AIT/Canada-Peru FTA/Canada-Colombia FTA Tendering Procedures: Generally only one firm has been invited to bid Attachment: None Non-Competitive Procurement Strategy: Exclusive Rights Comprehensive Land Claim Agreement: No Vendor Name and Address: Patterson Dental Canada Inc./Patterson Dentaire Canada Inc. 1205 boul. Henri-Bourassa ouest Montreal Quebec Canada H3M3E6 Nature of Requirements: PlanMeca X-Ray Systems Repairs - various locations across Canada

W8486-135088/A Holt, Judy Telephone No. - (306) 975-4051 ( ) Fax No. - (306) 975-5397

The Department of National Defence has a requirement for on-going repair and maintenance services for existing PlanMeca Digital X-R y Systems located in Canadian Forces Dental clinics across Canada

Sole Source Justification (d) Only one supplier is capable of performing the work PlanMeca states that maintenance requirements, annual instrument erification and calibration is required by authorized and qualifi d repair personnel for this equipment. In addition, the PlanMeca Promax and Proline XC equipment also us patented PlanMeca operating software that is unique to the equip ent and not interchangeable with other industry softwares availab e on the market. PlanMeca equipment must be inspected and repaired by authorized p rsonnel in order to ensure that any outstanding warranties remain valid and any repairs done the equipment are following the manufa turers standards. The Department of National Defence have distributed these instrum nts throughout their Dental Clinics across the country and requir continuity, interchangeability and compatibility of parts and co ponents, including, but not limited to, software and operating sy tems. PlanMeca Inc, the manufacturer of the X-Ray Systems, has identifi d Patterson Dental company as the sole authorized Canadian repres ntative for the provision of on-going repair and maintenance serv ces.

GCR Exemption (d) Only one supplier, person or firm is capable of performing th contract.

NAFTA Limited Tendering Reason d) for additional deliveries by the original supplier that are i tended either as replacement parts or continuing services for exi ting supplies, services or installations, or as the extension of xisting supplies, services or installations, where a change of su plier would compel the entity to procure equipment or services no meeting requirements of interchangeability with already existing equipment or services, including software to the extent that the nitial procurement of the software was covered by this Chapter.

AIT Article 506 12) to ensure compatibility with existing products, to recognize xclusive rights, such as exclusive licences, copyright and patent rights, or to maintain s ecialized products that must be maintained by the manufacturer or its representative.

Only known supplier Patterson Dental Canada Inc. 1205 boul. Henri-Bourassa ouest Montreal, Quebec H3M3E6 Canada

Estimated Value - $ 904,000 Cdn

Delivery Date: Above-mentioned

You are hereby notified that the government intends to negotiate ith one firm only as identified above. Should you have any questi ns concerning this requirement, contact the contracting officer i entified above.

An Advance Contract Award Notice (ACAN) allows departments and ag ncies to post a notice, for no less than fifteen (15) calendar da s, indicating to the supplier community that it intends to award good, service or construction contract to a pre-identified contr ctor. If no other supplier submits, on or before the closing date a Statement of Capabilities that meets the requirements set out n the ACAN, the contracting authority may then proceed with the a ard. However, should a Statement of Capabilities be found to mee the requirements set out in the ACAN, then the contracting autho ity will proceed to a full tendering process.

Suppliers who consider themselves fully qualified and available t provide the services/goods described herein, may submit a statem nt of capabilities in writing to the contact person identified in this Notice on or before the closing date of this Notice. The sta ement of capabilities must clearly demonstrate how the supplier m ets the advertised requirements.

The PWGSC file number, the contracting officer's name and the clo ing date of the ACAN must appear on the outside of the envelope i block letters or, in the case of a facsimile transmission, on th covering page.

The Crown retains the right to negotiate with suppliers on any pr curement.

Documents may be submitted in either official language of Canada.